Analysis of NOM-026-STPS-2008 in the manufacturing laboratory to improve productivity



Título del documento: Analysis of NOM-026-STPS-2008 in the manufacturing laboratory to improve productivity
Revista: Ingeniería. Investigación y tecnología
Base de datos: PERIÓDICA
Número de sistema: 000438761
ISSN: 1405-7743
Autores: 1
1
1
Instituciones: 1Instituto Tecnológico Superior de Guanajuato, Guanajuato. México
Año:
Periodo: Oct-Dic
Volumen: 20
Número: 4
País: México
Idioma: Inglés
Tipo de documento: Artículo
Enfoque: Analítico, descriptivo
Resumen en español En este artículo se realizó un diagnóstico para detectar que las señales de seguridad y salud cumplan con los requerimientos de la NOM-026-STPS-2008 dentro de un laboratorio de manufactura, el estudio se realizó conforme a lo establecido por la normatividad antes mencionada perteneciente a la Secretaría del Trabajo y Previsión Social, que es la entidad gubernamental encargada de realizar las inspecciones correspondientes de cumplimiento en el país de México en materia de colores y señales de seguridad e higiene con las que se encuentra operando un centro de trabajo. Dicho estudio se realizó con base en las medidas del plano arquitectónico del lugar a la ubicación de la maquinaria y herramientas. Se procedió a la ubicación de señalización de seguridad e higiene dentro del lugar, la identificación de existencia de instalaciones de emergencia, de riesgos y peligros dentro del área de trabajo, la detección del uso de señalética de obligación y prohibición que contribuya a controlar los riesgos. La limitación más importante para el acomodo de las señales se encuentra en la distribución inadecuada en el área de trabajo, sin embargo; se tuvo que adaptar el estudio a esta circunstancia. Con lo antes mencionado, se realiza una propuesta de reacomodo de la señalética que se ubica en puntos incorrectos, asimismo se mencionan las señales de seguridad que hacen falta en los puntos identificados dentro del lugar con sus especificaciones técnicas. Finalmente, se detecta un área de oportunidad para mejorar las condiciones de trabajo en un laboratorio de manufactura y, con ello, contribuir a evitar los accidentes y enfermedades ocupacionales aplicando medidas preventivas y correctivas con el uso adecuado de señalética en el área de trabajo
Resumen en inglés This paper presents a diagnostic to detect that the safety and health signals comply was made with the requirements of NOM-026-STPS-2008 within a manufacturing laboratory, the study was carried out in concordance with the provisions of the afore mentioned regulations pertaining to the Secretaría del Trabajo y Previsión Social, which is the government entity in charge of carrying out the corresponding compliance inspections in Mexico in terms of colors and signs of safety and hygiene which a work center is operating. This study was made based on the measurements of the architectural plan of the place to the location of the machinery and tools. Was made to the location of safety and hygiene signs within the place, the identification of the existence of emergency facilities, of risks and hazards within the work area, the detection of the use of signage of obligation and prohibition that helps to control the risks. The most important limitation for the arrangement of the signals is the inadequate distribution in the work area, however, the study had to adapt to this circumstance. With the aforementioned, a proposal is made to rearrange the signage that is located in incorrect points, as well as mentioning the safety signals that are needed in the points identified within the site with their technical specifications. Finally, an area of opportunity is detected to improve the working conditions manufacturing laboratory and thereby contribute to avoid accidents and occupational diseases therefore preventive and corrective measures are applied with the proper use of signage in an area of work
Disciplinas: Medicina
Palabras clave: Salud pública,
Seguridad laboral,
Higiene y seguridad,
Industria manufacturera,
Señalización,
Normas de seguridad,
Prevención de riesgos
Keyword: Public health,
Labor security,
Manufacturing industry,
Signaling,
Security norms,
Hygiene and safety,
Risk prevention
Texto completo: Texto completo (Ver HTML) Texto completo (Ver PDF)